Seismic Performances of High Rise R/C Frame Structures Reinforced with High Strength Rebars

Adi Mulya Sanjaya, Iswandi Imran


Construction of high rise buildings as supporting infrastructures for economic growth has increased significantly in numbers in many big cities around the world. In Indonesia, most of the high-rise buildings constructed are made of reinforced concrete structures. In principles, the use of high-strength concrete, coupled with high strength rebars for high rise r/c buildings will result in more efficient and more constructible r/c constructions. However, in Indonesia, the use of high strength rebars for seismic-resistant r/c buildings is still prohibited. SNI 2847:2013 Section 21 specifies that the yield strength for reinforcing bars used in structural elements of special moment resisting frames is limited to 420 MPa. This provision is meant to limit higher shear and higher bond demand in the structural elements assigned to dissipate seismic energy. This paper presents a study on the use of high strength rebars in seismic resistant r/c buildings. In the study, 20 story buildings located in a region with high seismicity are designed. Two types of rebars are used, i.e., those with the yield strength of 550 MPa and of 690 MPa. The building structures are designed as the special moment resisting frame. The seismic performances of the buildings are then investigated by performing non-linear time history analysis. Seven pairs of scaled ground motions are used for the analysis. From this analysis, the failure mechanism of r/c buildings reinforced with 550 MPa yield strength is governed by beam mechanism, while the buildings reinforced with 690MPa yield strength rebars shows failure mechanism dominated by story mechanism. Globally, the performance levels of the buildings are within the zone of Damage Control (i.e., between immediate occupancy and life safety). Based on the findings, some recommendations are proposed for the use of high strength rebars in the design of seismic resistant high rise r/c buildings.


ductility; non-linear time history analysis; performance based design; high strength rebars

Full Text:



Iswandi Imran dan Fajar Hendrik, “Perencanaan Lanjut Struktur Beton Bertulangâ€, Bandung Institute of Technology, Bandung, West Java, 2014.

Charles Pankow Foundation, “Determination of Yield Strength for Nonprestressed Steel Reinforcementâ€, Final Report RGA 04-13, Wiss, Janney, Elstner Associates, Inc. South Lake Avenue, 2013.

Constructed Facilities Laboratory, “A706 Grade 80 Reinforcement for Seismic Applicationâ€, Research Report No. RD-15-15, Department of Civil, Construction, and Environmental Engineering, North California State University.

Applied Technology Council, “Roadmap for The Use of High-Strength Reinforcement in Reinfoced Concrete Designâ€, ATC-115, Redwood City, California, 2014.

National Institute of Standards and Technology, “Use of High-Strength Reinforcement in Earthquake-Resistant Concrete Structuresâ€, NIST GCR 14-917-30, America, 2014.

H. Aoyama, “Design of Modern Highrise Reinforced Concrete Structureâ€, Vol 3, University of Tokyo, Japan, 2001.

H. Tavallali, “Cyclic Response of Concrete Beams Reinforced with Ultrahigh Strength Steelâ€, Ph. D. Thesis. Pennsylvania State University, Pennsylvania, 2011.

American Concrete Institute, “Design Guide for The Use of ASTM A1035/A1035M Grade 100 (690) Steel Bars for Structural Concreteâ€, America, ACI ITG-6R-10, 2010.

American Concrete Institute, “Building Code Requirements for Structural Concrete,†ACI 318-14, America, 2014.

American Society for Testing and Materials, “Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcementâ€, ASTM A706/A706-14, America, 2014.

American Society for Testing and Materials, “Deformed and Plain Carbon-Steel Bars for Concrete Reinforcementâ€, ASTM A615/A615M-15, America, 2015.

American Society for Testing and Materials, “Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcementâ€, ASTM A1035/A1035M-14, America, 2014.

T.Paulay and M.J.N. Priestley, “Seismic Design of Reinforced Concrete and Mansory Buildingsâ€, John Wiley & Sons, Inc., San Diego, 1991.

National Cooperative Highway Research Program, “Design of Concrete Structures Using High-Strength Steel Reinforcementâ€, NCHRP Report 679, Washington, 2011.

National Institute of Standards and Technology, “Seismic Design of Reinforced Concrete Special Moment Frameâ€, NEHRP Seismic Design Technical Brief No.1, Second Edition, America. 2016.

ICC Evaluation Sevice Report, “SAS Stress Steel Grade 97 Thread Bar Steel Reinforcing Bars and Couplersâ€, ESR-1163, New Jersey, 2016.

B. E. Drit Sokoli, “Seismic Performance of Concrete Column Reinforced with High Strength Steelâ€, Thesis, The University of Texas, 2014.

American Society of Civil Engineers, “Seismic Evaluation and Retrofit of Existing Buildingsâ€, ASCE/SEI 41-13, Virginia, 2013.

American Society of Civil Engineers, “Minimum Design Loads for Buildings and Other Structuresâ€, ASCE/SEI 7-10, Virginia, 2010.

R. Park and T. Paulay, “Reinforced Concrete Structuresâ€, Department of Civil Engineering, University of Christchurch, New Zealand, 1975.

Finley A. Charney, Ph.D., P.E, “Seismic Load : Guide to The Provision of ASCE 7-10â€, American Society of Civil Engineers, Virginia, 2010.

Standar Nasional Indonesia, “Persyaratan Beton Struktural untuk Bangunan Gedungâ€, SNI 2847:2013, Jakarta, 2013.

Standar Nasional Indonesia, “Tata Cara Perencanaan Ketahanan Gempa untuk Struktur Bangunan Gedung dan Non Gedungâ€, SNI 1726:2012, Jakarta, 2012.

Standar Nasional Indonesia, “Beban Minimum untuk Perancangan Bangungan Gedung dan Struktur Lainâ€, SNI 1727:2013, Jakarta, 2013.

Earthquake Engineering Research Institute, “Practical Guidelines to Select and Scale Earthquake Records for Nonlinear Response History Analysis of Structureâ€, USGS File Report, Amerika, 2010.



  • There are currently no refbacks.

Published by INSIGHT - Indonesian Society for Knowledge and Human Development